Struct Clkcr

#[repr(transparent)]
pub struct Clkcr(pub u32);

Expand description

The SDMMC_CLKCR register controls the SDMMC_CK output clock, the SDMMC_RX_CLK receive clock, and the bus width.

Tuple Fields§

§0: u32

Implementations§

§

impl Clkcr

pub const fn clkdiv(&self) -> u16

Clock divide factor This bit can only be written when the CPSM and DPSM are not active (CPSMACT = 0 and DPSMACT = 0). This field defines the divide factor between the input clock (SDMMCCLK) and the output clock (SDMMC_CK): SDMMC_CK frequency = SDMMCCLK / [2 * CLKDIV]. 0xx: etc.. xxx: etc..

pub fn set_clkdiv(&mut self, val: u16)

Clock divide factor This bit can only be written when the CPSM and DPSM are not active (CPSMACT = 0 and DPSMACT = 0). This field defines the divide factor between the input clock (SDMMCCLK) and the output clock (SDMMC_CK): SDMMC_CK frequency = SDMMCCLK / [2 * CLKDIV]. 0xx: etc.. xxx: etc..

pub const fn pwrsav(&self) -> bool

Power saving configuration bit This bit can only be written when the CPSM and DPSM are not active (CPSMACT = 0 and DPSMACT = 0) For power saving, the SDMMC_CK clock output can be disabled when the bus is idle by setting PWRSAV:

pub fn set_pwrsav(&mut self, val: bool)

Power saving configuration bit This bit can only be written when the CPSM and DPSM are not active (CPSMACT = 0 and DPSMACT = 0) For power saving, the SDMMC_CK clock output can be disabled when the bus is idle by setting PWRSAV:

pub const fn widbus(&self) -> u8

Wide bus mode enable bit This bit can only be written when the CPSM and DPSM are not active (CPSMACT = 0 and DPSMACT = 0)

pub fn set_widbus(&mut self, val: u8)

Wide bus mode enable bit This bit can only be written when the CPSM and DPSM are not active (CPSMACT = 0 and DPSMACT = 0)

pub const fn negedge(&self) -> bool

SDMMC_CK dephasing selection bit for data and Command. This bit can only be written when the CPSM and DPSM are not active (CPSMACT = 0 and DPSMACT = 0). When clock division = 1 (CLKDIV = 0), this bit has no effect. Data and Command change on SDMMC_CK falling edge. When clock division >1 (CLKDIV > 0) & DDR = 0: - SDMMC_CK edge occurs on SDMMCCLK rising edge. When clock division >1 (CLKDIV > 0) & DDR = 1: - Data changed on the SDMMCCLK falling edge succeeding a SDMMC_CK edge. - SDMMC_CK edge occurs on SDMMCCLK rising edge. - Data changed on the SDMMC_CK falling edge succeeding a SDMMC_CK edge. - SDMMC_CK edge occurs on SDMMCCLK rising edge.

pub fn set_negedge(&mut self, val: bool)

SDMMC_CK dephasing selection bit for data and Command. This bit can only be written when the CPSM and DPSM are not active (CPSMACT = 0 and DPSMACT = 0). When clock division = 1 (CLKDIV = 0), this bit has no effect. Data and Command change on SDMMC_CK falling edge. When clock division >1 (CLKDIV > 0) & DDR = 0: - SDMMC_CK edge occurs on SDMMCCLK rising edge. When clock division >1 (CLKDIV > 0) & DDR = 1: - Data changed on the SDMMCCLK falling edge succeeding a SDMMC_CK edge. - SDMMC_CK edge occurs on SDMMCCLK rising edge. - Data changed on the SDMMC_CK falling edge succeeding a SDMMC_CK edge. - SDMMC_CK edge occurs on SDMMCCLK rising edge.

pub const fn hwfc_en(&self) -> bool

Hardware flow control enable This bit can only be written when the CPSM and DPSM are not active (CPSMACT = 0 and DPSMACT = 0) When Hardware flow control is enabled, the meaning of the TXFIFOE and RXFIFOF flags change, please see SDMMC status register definition in Section56.8.11.

pub fn set_hwfc_en(&mut self, val: bool)

Hardware flow control enable This bit can only be written when the CPSM and DPSM are not active (CPSMACT = 0 and DPSMACT = 0) When Hardware flow control is enabled, the meaning of the TXFIFOE and RXFIFOF flags change, please see SDMMC status register definition in Section56.8.11.

pub const fn ddr(&self) -> bool

Data rate signaling selection This bit can only be written when the CPSM and DPSM are not active (CPSMACT = 0 and DPSMACT = 0) DDR rate shall only be selected with 4-bit or 8-bit wide bus mode. (WIDBUS > 00). DDR = 1 has no effect when WIDBUS = 00 (1-bit wide bus). DDR rate shall only be selected with clock division >1. (CLKDIV > 0)

pub fn set_ddr(&mut self, val: bool)

Data rate signaling selection This bit can only be written when the CPSM and DPSM are not active (CPSMACT = 0 and DPSMACT = 0) DDR rate shall only be selected with 4-bit or 8-bit wide bus mode. (WIDBUS > 00). DDR = 1 has no effect when WIDBUS = 00 (1-bit wide bus). DDR rate shall only be selected with clock division >1. (CLKDIV > 0)

pub const fn busspeed(&self) -> bool

Bus speed mode selection between DS, HS, SDR12, SDR25 and SDR50, DDR50, SDR104. This bit can only be written when the CPSM and DPSM are not active (CPSMACT = 0 and DPSMACT = 0)

pub fn set_busspeed(&mut self, val: bool)

Bus speed mode selection between DS, HS, SDR12, SDR25 and SDR50, DDR50, SDR104. This bit can only be written when the CPSM and DPSM are not active (CPSMACT = 0 and DPSMACT = 0)