Struct Cr1

#[repr(transparent)]
pub struct Cr1(pub u32);

PWR control register 1

Tuple Fields

0: u32

Implementations

impl Cr1

pub const fn lpds(&self) -> bool

Low-power Deepsleep with SVOS3 (SVOS4 and SVOS5 always use low-power, regardless of the setting of this bit)

pub fn set_lpds(&mut self, val: bool)

Low-power Deepsleep with SVOS3 (SVOS4 and SVOS5 always use low-power, regardless of the setting of this bit)

pub const fn pvde(&self) -> bool

Programmable voltage detector enable

pub fn set_pvde(&mut self, val: bool)

Programmable voltage detector enable

pub const fn pls(&self) -> u8

Programmable voltage detector level selection These bits select the voltage threshold detected by the PVD. Note: Refer to Section Electrical characteristics of the product datasheet for more details.

pub fn set_pls(&mut self, val: u8)

Programmable voltage detector level selection These bits select the voltage threshold detected by the PVD. Note: Refer to Section Electrical characteristics of the product datasheet for more details.

pub const fn dbp(&self) -> bool

Disable backup domain write protection In reset state, the RCC_BDCR register, the RTC registers (including the backup registers), BREN and MOEN bits in PWR_CR2 register, are protected against parasitic write access. This bit must be set to enable write access to these registers.

pub fn set_dbp(&mut self, val: bool)

Disable backup domain write protection In reset state, the RCC_BDCR register, the RTC registers (including the backup registers), BREN and MOEN bits in PWR_CR2 register, are protected against parasitic write access. This bit must be set to enable write access to these registers.

pub const fn flps(&self) -> bool

Flash low-power mode in DStop mode This bit allows to obtain the best trade-off between low-power consumption and restart time when exiting from DStop mode. When it is set, the Flash memory enters low-power mode when D1 domain is in DStop mode.

pub fn set_flps(&mut self, val: bool)

Flash low-power mode in DStop mode This bit allows to obtain the best trade-off between low-power consumption and restart time when exiting from DStop mode. When it is set, the Flash memory enters low-power mode when D1 domain is in DStop mode.

pub const fn svos(&self) -> u8

System Stop mode voltage scaling selection These bits control the VCORE voltage level in system Stop mode, to obtain the best trade-off between power consumption and performance.

pub fn set_svos(&mut self, val: u8)

System Stop mode voltage scaling selection These bits control the VCORE voltage level in system Stop mode, to obtain the best trade-off between power consumption and performance.

pub const fn avden(&self) -> bool

Peripheral voltage monitor on VDDA enable

pub fn set_avden(&mut self, val: bool)

Peripheral voltage monitor on VDDA enable

pub const fn als(&self) -> u8

Analog voltage detector level selection These bits select the voltage threshold detected by the AVD.

pub fn set_als(&mut self, val: u8)

Analog voltage detector level selection These bits select the voltage threshold detected by the AVD.

Trait Implementations

impl Clone for Cr1

fn clone(&self) -> Cr1

Returns a copy of the value.

fn clone_from(&mut self, source: &Self)

Performs copy-assignment from source.

impl Default for Cr1

fn default() -> Cr1

Returns the “default value” for a type.

impl PartialEq for Cr1

fn eq(&self, other: &Cr1) -> bool

Tests for self and other values to be equal, and is used by ==.

fn ne(&self, other: &Rhs) -> bool

Tests for !=. The default implementation is almost always sufficient, and should not be overridden without very good reason.

impl Copy for Cr1

impl Eq for Cr1

impl StructuralPartialEq for Cr1